Monday, July 23, 2012

How to fake a scar

You can achieve scars like this using rigid collodion
-->




Now I know I have talked about scars in other post but I figured since scars can appear different depending on age I’d do a post to get a little more in depth on them.  

For this you will need:
- Rigid collodion
- Astringent
- Cream makeup scar wheel
- Skin tone cream make up
- Makeup sponges
- Small brushes
- Setting powder
- Brush Cleaner
- Powder puff

Basic preparation steps:

  1. Decided how new the scar will be (depending on if this scar is shallow or deep.)
  2. Research pictures of scars (shallow or deep)
·       A makeup artist always has reference pictures of what they are going to do.
  1. Clean the area of skin with astringent
  2. Apply a thin layer of rigid collodion
  3. Allow the rigid collodion to dry
  4. Repeat steps one and two until desired result is achieved
·       Shallow scars may require up to 4 or 5 layers
·       Deep scars may require only 2 or 3 layers

The next few steps are for shallower scars:

1.     Using a makeup sponge lightly add some red makeup directly onto the scar and blend out about a centimeter or two, not even
2.     Powder to set the make up
3.     If the scar still appears to faint or is to close to the color of the surrounding, now pinkish, skin take the small brush and a little bit of red and brush it into the scar
·       You may need to blend the red with some skin tone to achieve your desired results. This can be done before or after the application. I would suggest after. You can use it to blend the color out a little further, almost like a safety net.
4.     Take a clean edge of your sponge and dab at the scar until it is blended almost evenly
5.     Powder to set the makeup
6.     Using a makeup sponge lightly apply a think layer of skin tone makeup to the scar and surrounding area
7.     Powder to set makeup
8.     Repeat steps 6-7 until desired result is achieved

The next few steps are for deeper scars:

1.     Using a small brush lightly add some red makeup directly onto the scar
2.     Using a makeup sponge blend out, no centimeter or two, onto the skin
3.     Powder to set the makeup
4.     Using a small makeup brush, the same one is ok, add a small amount of purple to the scar
5.     Using a clean side of your wedge blend the purple out, no more then a centimeter, onto the skin
6.     Powder to set the make up
7.     If still not the desired result repeat steps 4-6 using blue
8.     Using a makeup sponge apply a thin layer of skin tone make up to your scar and the surrounding area
9.     Powder to set the makeup
10.   Repeat step 8-9 until desired result is achieved.

That is how you fake a scar, new or old. If you wish to spice up a brand new scar you can add some congealed blood directly onto the rigid collodion after you are done shading the area with red makeup. This gives the appearance of a recent cut. 


Scars combine with bruises always give a cool effect.

Here are some helpful links




Sunday, July 1, 2012

How to Make a Severed Head

-->
This week I am going to tell you all how to make a severed head.


The supplies you are going to need are:
1.     A head mold
2.     Casting latex
3.     Poly foam
4.     Acrylic paint
5.     A hot glue gun
6.     Hot glue
7.     Fake eyes
8.     A wig or crepe hair
9.     A dremel
10. Something to hold the two half’s of the head mold together
11. Packing peanuts (optional)
12. Screwdriver (optional)
13. Scissors
14. Spongy material

The first step is to tie your two halves of your mold together very tightly.

The second step is to slush the mold. To do this you pour the casting latex into the head mold to about the half way or quarter point. They you slowly rotate your mold while pouring out the latex back into it’s original container.

Step three let the latex dry over night, or up against a fan for 6 to 12 hours. You want to make sure it has set and is no longer wet, sticky, tacky, in any way not completely dry.

Step four. Mix the two active components of your poly foam. It should be about a 25 to 12 ratio.

If you are using the packing peanuts add them in first and make sure they are up to at least the half waypoint. Then you add your poly foam. You ratio should be about 14 to 7.

Step five. Once your foam has risen and set, about 20 to 30 minutes after you added it, you are now ready to pull your mold. You may now untie your mold and carefully pull it apart. You may need to use a screwdriver to separate the two halves.

Step six. Once you have pulled the mold it is time to dremel. You must dermal down the edges where there is a seam. You need to make this as smooth and invisible as possible.

Step seven. Once you are done dremaling you now need to trim the excess foam from about the neck. SAVE THIS! DO NOT THROW IT AWAY!

Step eight. Now heat up your hot glue gun and decide how you will position the let over latex that you have trimmed off the neck. This will be your arteries, guts and gore factor. NOTE! Do not glue these into the center! Leave the center open incase you decided to add a vertebra.

Step nine. Glue the latex.

Step ten. Mix your paint with some of your casting latex. Attempt to get a dark purplish reddish color.

Step eleven. Sponge paint the white poly foam and latex.

Step twelve. Let the paint dry.

Step thirteen. Cut out the eye area.

Step fourteen. Choose a pair of eyes and gently insert them into the now open eye area.

Step fifteen. Add some blues and reds very subtly around the neck area. This just adds some realness and depth to your head.

Step sixteen. Pick out a wig and hot glue it to your head.

Optional step seventeen. If you wish you can use more paint to apply make up to your head, if you wish it to be a girl, or to add color to the lips and cheeks.

Optional step eighteen. You can now add some of your reddish latex to the hair and on your head’s face to make it appear beaten.

Optional step eighteen. If you wish you can use more paint to apply make up to your head, if you wish it to be a girl, or to add color to the lips and cheeks.

Hooray! You now have your very own severed head. Use it at Halloween, in a movie, to scare your friends, scare your mom, your teacher, a person in a car accident (well that would just be rude). What I’m trying to say is enjoy it!

For more tips on how to make your own head or other body parts check out these links.